Exploring Plumbing Fundamentals When You Install a Bathtub
Exploring Plumbing Fundamentals When You Install a Bathtub
Blog Article
The author is making several great annotation related to How to Install a Bathtub overall in this article beneath.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately difficult task. If the old tub is readily accessible, the task can move speedily; if you need to open a wall surface to remove the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the task as well as fit attempting it. Rather than employing a service provider to take over a halfway-completed job, it is much better to think about using one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This article will aid you mount a brand-new bath tub in your shower room if you have currently bought a brand-new bathtub as well as don't require to alter the setup of your previous water system pipes.
Your tools as well as material list should comprise the following:
Planning for the Setup
Firstly, the sustaining framework provided with the bath must be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Making use of both wood boards under its feet, place the bath tub in the called for position. The wooden boards are practical in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To set up taps, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and check all joints as well as new pipework for leakages and also tighten them if necessary. Fill the bath tub as well as likewise inspect the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been utilized at the very least once as this will resolve it into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in area in between the faucet and the sink. Protect the faucet in position with the maker given backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in problems with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and also can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the marketplace. It is suggested to fit the tiles using waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that piece on Installing A Bathtub when doing a search on the internet. So long as you liked our blog posting plz remember to share it. Thanks so much for going through it.
Your solution? Just a ring. Report this page